Expert Garage Door Solutions in Ponte Vedra Beach

Installed T-handle exterior lock on 8'9" x 6'3" CloPay uninsulated door. Customer reported lock had seized due to salt air corrosion. Inspection 5/11 confirmed seizure; customer approved estimate same day and lock was ordered. Returned 5/14 to complete replacement. Removed corroded lock, installed new T-handle. Door operating properly. Customer satisfied.

Completed install of LiftMaster 6690L belt drive opener. Removed failed unit, installed new opener, belt rail, wall button, and sensors, adapting to existing wiring. Programmed open/close force settings, 3 handheld remotes, and 1 keypad. Demoed operation for customer and assisted with Wi-Fi connection setup. Job complete, customer walked through full functionality.

Performed maintenance, roller replacement, and bottom seal replacement on a 16x8 uninsulated door with LiftMaster opener. Customer reported noise and a hanging bottom seal. Inspection found opener as primary noise source, with clicking rollers; old bottom seal cracked. Replaced bottom seal, installed 12 new rollers, lubricated rollers/hinges/springs. Door and opener functioning properly.

Transparent and trust-building: Jacksonville Beach homeowners — sometimes a garage door problem runs deeper than it first appears. When our technician arrived, the homeowner's door had stopped working and the left cable had come off. Inspection revealed a bent track and a loose wall bracket — not a simple fix. We reset the door, reset both drums, re-tensioned the springs, straightened the track bracket, and drilled a new lag to secure it to the wall. We got the customer's car out safely. That's what honest service looks like — we don't close a job until it's right. That's Wagmore.

Installed new LiftMaster 6690L belt drive opener with 2 remotes and keypad. Removed old opener; installed new rail, motor, sensors, wall button, and keypad. Programmed remotes, set open/close limits, and tested thoroughly. Completed full door maintenance/lubrication and replaced all rollers with new quiet nylon rollers. Connected opener to customer's Wi-Fi, confirmed proper operation, and walked customer through all features.

Replaced opener on 16x8 vinyl insulated door for intermittent stopping. Inspection confirmed opener malfunction and undersized springs causing improper door balance. Customer approved opener replacement quote. Installed LiftMaster 6580L with 8' belt rail, safety sensors, wall button, and 1 remote. Covered by 6-year motor/belt warranty and 5-year labor warranty.

Jacksonville Beach homeowners—our $0 Safe & Sound Inspection on an 8x7 door with a Chamberlain chain drive uncovered a faulty sensor, a non-communicating keypad, and old extension springs running without safety cables. Our tech completed a torsion spring conversion, resolved every issue found, and left the door and opener fully operational. That's Wagmore.

Completed safety inspection on 16x7 Wayne Dalton door w/ Genie 2028. Customer reported screeching noise, requested roller maintenance. Replaced all 10 rollers (nylon), lubricated hinges/rollers, adjusted operator limits. Found screeching from TorqueMaster spring; customer approved conversion to black springs. Installed new springs, cables, drums, bearings; balanced door, re-tested operator—runs smooth, no noise.

Performed Safe & Sound Inspections on two steel-back insulated doors (16x7 and 8x7). Customer reported a broken spring on the 16x7 door, which was confirmed during inspection. Door was weighed to verify spring sizing — existing springs were correctly sized for the door weight. J-arm was also found to be bent. Replaced both torsion springs on the 16x7 door, installed new rollers on both doors, and completed full maintenance/lubrication on both doors. J-arm addressed. Both doors operating correctly upon completion.

Arrived to failed torsion springs; customer had signed estimate for replacement. Measured door and confirmed correct spring size needed. Removed failed springs, installed two new .25 x 30" springs with steel center bearing. Lubricated springs, tested door balance and operation. Reset open/close limits on operator, confirmed proper function with and without opener. Reviewed completed work with customer — fully satisfied.

Customer reported the door opening fine but slamming down—inspection found a broken torsion spring. Measured and confirmed matching standard black springs were on the truck. Customer approved estimate; removed both failed springs and installed two new standard black torsion springs. Balanced the door properly, reattached to the operator rail, and confirmed smooth, correct operation.