Recent Jobs For Wagmore Garage Doors

August 7, 2026 | Jacksonville,, FL

Installed LiftMaster 2220L opener on 10x8 steel insulated Amarr door. Customer reported remotes not staying connected — diagnosed as bad receiver on logic board of original 1997 opener. Customer approved replacement estimate. Removed old opener; installed new LiftMaster 2220L with two remotes, wall button, sensors, and keypad. Customer reviewed completed work, satisfied. ...

August 6, 2026 | Jacksonville, FL

Summer maintenance check-up on 16x7 and 8x7 doors, LiftMaster belt drive openers. Removed and replaced rollers with 10 new nylon rollers per door (20 total). Lubricated hinges, rollers, bearings, and springs on both doors. Reset travel limits on both openers. Added spring tension on the 16x7 door. Tightened belts on both openers. ...

August 5, 2026 | Green Cove Springs, FL

Installed two LiftMaster 6690L openers on 16x7 uninsulated Amarr doors, replacing existing units. Each opener includes sensors, keypad, wall button, and two remotes. Belts tensioned properly, travel limits set. Assisted customer with myQ setup; all four remotes programmed for both doors; keypad set to customer's code. Customer reviewed and satisfied. ...

August 4, 2026 | Orange Park, FL

Double spring replacement: removed old springs, shaft, and cables; installed two WagMore Forever Springs with new shaft, center bearing, and cables. Door weighed for proper spring size, springs wound to correct tension. Removed old opener and installed new LiftMaster 6690L with new sensors, wall button, keypad, and two remotes. Customer ...

August 3, 2026 | Middleburg, FL

Arrived on-site and diagnosed a broken torsion spring. Reviewed findings with customer and received approval to proceed. Removed the failed spring(s) and installed new torsion springs matched to door weight/cycle specs. Performed full operational testing post-install — door is cycling smoothly with no binding or noise. Customer confirmed satisfaction ...

July 31, 2026 | Nocatee, FL

Performed double torsion spring conversion on 16x7 Wayne Dalton door with Genie 2028 opener. Removed failed TorqueMaster system. Installed two Forever Springs, new center bearing/plate, drums, cables, and shaft. Reprogrammed opener travel limits, tightened chain, lubricated bearings/rollers/springs/hinges. Door and opener operating properly.

July 30, 2026 | Jacksonville, FL

16x7 Wayne Dalton door, Genie 2028 opener — TorqueMaster conversion. Customer reported door sticking on initial daily opening; door would stay open only via manual emergency release, then wouldn't hold at full open. Diagnosis: weak TorqueMaster spring + sticky vinyl trim residue. Customer approved TM conversion only (declined trim). Installed new torsion springs, ...

July 29, 2026 | Jacksonville, FL

Completed door reset on 16x7 Clopay insulated door with Genie screwdriver opener. Customer requested top/bottom brackets, two struts, and reset. Installed struts, top fixtures, and bottom brackets before winding springs. Tightened cables into drums, added spring tension, confirmed balance — door operating properly. Opener sensors found failed, preventing down travel. ...

July 28, 2026 | Saint Augustine, FL

Replaced opener on 16x7 Wayne Dalton door. Inspection revealed a bad gear inside the existing Genie opener. Door was already torsion spring converted with nylon rollers. Customer approved estimate for LiftMaster 6580L belt drive opener. Removed old unit; installed new 6580L with remote, sensors, wall button, and keypad. Customer reviewed ...

July 27, 2026 | Middleburg, FL

Installed a 16x7 N. Woods NW 3000 garage door, customer-supplied Chamberlain belt-drive opener retained per customer request. Removed and hauled away the old door, installed new trim around the opening. Walked the customer through the completed work — they were satisfied. Door and opener tested and confirmed working properly at time of ...

July 24, 2026 | Jacksonville, FL

Customer reported the door opening fine but slamming down—inspection found a broken torsion spring. Measured and confirmed matching standard black springs were on the truck. Customer approved estimate; removed both failed springs and installed two new standard black torsion springs. Balanced the door properly, reattached to the operator rail, ...

July 23, 2026 | Saint Augustine, FL

Installed LiftMaster 8500W... wait, let me match this correctly — LiftMaster 6690L belt drive opener on 16x7 overhead door as part of summer ready check-up. Removed old opener; installed new unit with sensors, wall button, two remotes, and keypad. Replaced all 10 rollers. Adjusted spring tension. Lubricated hinges, rollers, springs, bearings, and ...

July 22, 2026 | Nocatee, FL

16x7 Wayne Dalton opener replacement. Customer reported opener failure following an electrical storm. Inspection revealed a bad circuit board. Estimate approved for new LiftMaster 6690L belt drive opener. Removed old unit; installed new opener with sensors, wall button, two remotes, and keypad. Customer reviewed and approved completed work. Door and ...

July 21, 2026 | Nocatee, FL

Installed two LiftMaster 6690 belt drive openers with 7' rails and a new torsion spring system (shaft, bearings, plates, cables, drums) on a single-car door. Balanced the door, mounted openers on existing angle iron, programmed settings/remotes/keypads. Lubricated all moving parts, cleaned up, and reviewed operation/emergency release with customer. ...

July 20, 2026 | Saint Augustine, FL

Performed full maintenance, dent repair, and bottom seal replacement on a 16x7 Wayne Dalton door with Genie 2028 opener. Repaired panel dent, removed old bottom seal and installed new seal with retainer, lubricated springs, rollers, cables, bearings, and hinges. Tightened opener chain and added spring tension. Relocated sensors lower to clear ...