Anthony Kopp

Anthony Kopp

Field Specialist

Customers love working with Anthony Kopp

See All

Jobs Completed by Anthony Kopp

See All

Fleming Island, FL

November 18, 2026

On arrival, customer reported a broken garage door spring. Customer opted for a double spring replacement and enrolled in the WAGS Family Plan with roller replacement. Replaced both springs and installed new rollers. Completed 18-point inspection and lubricated all new rollers and hinges. Door tested and is running smoothly.

Orange Park, FL

November 17, 2026

Customer reported the garage door would travel down a few inches, stop, and reverse. Completed 18-point inspection and found the opener’s travel limits needed to be reset. Customer approved the $199 service call/limit set fee. Reset the open and close limits and ran the door through full cycles; door is now operating normally.

Saint Augustine, FL

November 16, 2026

Upon arrival, the garage door would not close due to a sensor fault. Completed our 18-point inspection and found the safety sensors were defective and needed replacement. Customer approved the sensor replacement; new sensors were installed, aligned, and tested. Door is now in good working order.

Saint Augustine, FL

November 13, 2026

Customer reported door opening very slowly. Completed 18-point inspection; diagnosed defective TorqueMaster spring system. Recommended torsion conversion for smoother, faster operation and reduced opener strain. Customer approved. Converted to standard torsion: installed Forever Springs, drums, cables, and bearings. Door now operates quickly and smoothly.

Saint Augustine, FL

November 12, 2026

On arrival, the customer’s door would not open. The 18-point inspection found a broken spring in the TorqueMaster system. The tech recommended a torsion conversion, and the customer approved it. The tech converted the door to a standard torsion system and installed a new bar, bearings, drums and cables, plus our Forever Spring. The garage door is now in very good working order.

Fruit Cove , FL

November 11, 2026

Customer requested the 123 Maintenance Plan and a weather seal replacement. Did the 18-point safety inspection and all maintenance plan services. Lubricated the rollers, hinges and tracks. Installed new weather stripping. Tested the door after service and it’s working properly.

Saint Johns, FL

November 10, 2026

Arrived to a broken TorqueMaster spring system. Completed the 18-point inspection and recommended a torsion conversion. Customer approved the conversion and also enrolled in the 123 Wags Family Plan. Installed new Forever Springs, drums, bearings, cables and a new torsion bar. Lubricated all hinges and rollers. Tested the door and it’s running smoothly.

Jacksonville, FL

November 9, 2026

Our technician installed a new 16x7 Lincoln LI 1000 garage door and connected it to the customer’s existing opener. The door was tested several times after installation, and it opened, closed, and ran properly each time. As of the end of this visit, the door and opener are working as they should.

Saint Johns , FL

November 6, 2026

Customer requested a roller/hinge lube and tune-up. The 18-point inspection found the openers on all four doors were very old, and I talked with the customer about replacing them. Customer also asked for all rollers to be replaced. Installed four new 1 HP belt-drive openers, new safety sensors and new wall-mount controls. All four doors tested and are working well. Customer very satisfied; paid by card.

Jacksonville, FL

November 5, 2026

On arrival, the customer asked for the 123 Maintenance Plan on both of his garage doors, a single and a double. The technician completed the 18-point inspection and performed full maintenance on both doors. Both doors are now opening and closing smoothly. The customer was satisfied with the service and paid by card. Both doors are now enrolled in the 123 Maintenance Plan.

Nocatee, FL

November 4, 2026

Upon arrival, the customer requested a new ¾ HP chain-drive opener. The technician installed the opener along with new safety sensors and a wall-mounted control, then reset the travel limits for proper operation. The door was tested and is in good working order, and the customer was satisfied with the completed work.

Saint Augustine, FL

November 3, 2026

Customer requested a door reset. Upon starting the reset, the technician found the springs would not come loose from the bar, preventing the reset from being completed. Advised the owner that the bar, springs, and drums needed replacement, and the customer approved. Installed new springs, drums, bearings, and bar. Door is in good working order and the customer is satisfied with the repair.

Orange Park , FL

November 2, 2026

On arrival, found a spring bracket held by only one bolt and halfway out of the wall. Replaced the bracket and reattached the springs to the wall. Garage door is in good working order.

Ponte Vedra, FL

October 30, 2026

Upon arrival, technician found the customer’s TorqueMaster spring system broken. Reviewed the issue with the customer, who approved a conversion to a standard torsion system. Performed an 18-point inspection and completed the conversion, installing our Forever Spring along with new cables, drums, torsion bar, and bearing plates. Door is in good working condition and the customer is satisfied.

Saint Augustine, FL

October 29, 2026

Upon arrival, customer needed a torsion conversion. Completed the full conversion, installing new springs, drums, cables, torsion bar, and bearings, then reset the opener limits. At the customer’s request, also replaced the rollers. Completed our 18-point inspection and lubricated all hinges, rollers, springs, and bearings.

Jacksonville, FL

October 28, 2026

Removed the existing garage door and opener. Installed a new Lincoln LI 1000 16x7 garage door and a new LiftMaster chain drive opener, along with a new wall button and safety sensors. Ran all new wiring throughout the system. Lubricated the door for smooth, quiet operation. Tested all door and opener functions before leaving, and everything is working properly at this time.

Saint Augustine, FL

October 27, 2026

Replaced failed opener. Customer’s reset attempts led to chain coming off; door inoperable. Found damaged chain, sprocket, and limit switch. Reviewed repair vs. replacement; customer chose replacement. Installed LiftMaster 6690L 1-1/4 HP belt drive with wall button, sensors, keypad, and 2 remotes. Set open/close/force, programmed accessories, tested, and trained customer.

Saint Augustine, FL

October 26, 2026

TorqueMaster conversion – 16x7 Wayne Dalton w/ Genie 2028. One TM spring broken; door too heavy to lift, estimate approved. Weighed door to size springs; installed new springs, shaft, bearings, bearing plates, cables, drums & nylon rollers. Tensioned, verified manual balance, lubed door/opener, reset limits & force. Lifetime parts/labor warranty w/ annual WagMore maintenance.

Ponte Vedra, FL

October 23, 2026

TorqueMaster conversion, 16x7 Wayne Dalton. Customer heard a loud bang; door stopped working. Safe & Sound Inspection: broken TorqueMaster spring (door 100+ lbs), worn rollers, no recent maintenance. Installed new springs, shaft, bearings, plates, drums, cables; tensioned and tested. Opener limits/force reset. Lifetime warranty w/ annual WagMore maintenance.

Elkton,

October 22, 2026

Following reports of improper door operation, our technician completed an 18-point inspection, confirmed the safety sensors were defective, and installed replacements with customer authorization.

Saint Johns, FL

October 21, 2026

Completed TorqueMaster-to-torsion conversion on a 16x7 Wayne Dalton door. Released tension and removed the full TorqueMaster system. Installed new torsion springs, shaft, bearing plates, center bearing, cables, drums, and nylon rollers. Tensioned and hand-balanced the door, reset operator open/close limits and force, and tested by hand and with the operator; working properly. Lubricated all new parts and hinges. Lifetime parts and labor warranty with annual WagMore service.

Jacksonville, FL

October 20, 2026

Customer reported the door only worked manually. Inspection found a non-functional opener with signs of prior repairs, and springs that had broken and been welded back together. Wood door was in poor condition. Removed the old door, opener, and accessories. Installed a new Lincoln LI 1000 non-insulated door and a LiftMaster 1-1/4 HP opener with a new wall button, sensors, and keypad. Lubricated, tested multiple times, and left 2 remotes.

Saint Augustine, FL

October 19, 2026

Upon arrival, customer reported their garage door opener was old and noisy and requested replacement with a new LiftMaster 1¼ HP belt-drive opener. Replaced opener, safety sensors, wall control, and keypad. Reset travel limits and completed 18-point inspection. Door is in good working order.

Saint Augustine, FL

October 16, 2026

Property manager rescheduled the original appointment to Monday (customer not home). On Monday’s visit, tech found the door needed a complete reset. Customer approved the $599 door reset. Cables were reset and the spring rewound to proper tension. Door tested and operating properly.

Orange Park , FL

October 15, 2026

Removed existing opener and installed a new LiftMaster 2220L chain drive opener with rail, safety sensors, wall button, and two remotes. Adapted to existing wiring and angle iron. Programmed open/close limits and force settings, then tested and confirmed the door and opener are operating properly. Set up Wi-Fi and showed the customer how to use the app, remotes, wall button, and emergency release.

Palm Coast , FL

October 14, 2026

Installed new insulation on the double door and single door. Installed a new LiftMaster 1¼ HP belt-drive opener, along with a new wall button, keypad, and safety sensors on the double door. Replaced rollers on both doors with whisper-quiet nylon rollers. Tested all operations on both doors. Everything is working properly at this time.

Saint Augustine, FL

October 13, 2026

Customer reported opener acting up and slow door travel. Replaced with LiftMaster 1¼ HP belt drive, new sensors, wall control, and keypad. Found a TorqueMaster spring system; advised replacement, customer approved. Completed torsion conversion: Forever Springs, new shaft, drums, cables, bearing plates. 18-point inspection done; rollers and hinges lubed. Door working great.

Saint Johns , FL

October 12, 2026

Arrived to find the customer’s TorqueMaster spring system broken. Customer approved the estimate for a full TorqueMaster-to-torsion conversion. Installed WagMore Forever Springs, new drums, new cables, and new end brackets, then reset the opener limits. Door tested and operating smoothly. New components are covered under our Forever Warranty with biennial WagMore service.

Saint Augustine, FL

October 9, 2026

Arrived on site and found a broken spring. Removed the broken spring and installed a brand-new Forever spring. Rewound the springs, tightened the cables and drums, and reset the opener limits. Door tested and in good working order; customer is satisfied with the repair.

St. Johns , FL

October 8, 2026

Today we installed a brand-new Lincoln LI 1000 garage door in white, giving the home a clean, refreshed look along with improved durability and performance. To pair with the new door, we also installed a new 1 1/4 HP LiftMaster belt drive opener, known for its strong lifting power and smooth, quiet operation. The upgrade was completed with a new wall button, new safety sensors, and a new exterior keypad for convenient, secure access. Before leaving, our technician tested every function of the door and opener, including opening, closing, safety reversal, and keypad entry, to confirm everything was running correctly. Everything is working properly at this time, and the customer is all set with a safe, reliable, and quiet new garage door system.

Saint Augustine, FL

October 7, 2026

Customer reported the opener arm (J-arm) bracket had broken off the door. Replaced the bracket and completed a 16-point inspection; door is in good working order and running smoothly up and down. Opener is older. Advised on replacement, but the customer is moving within a year and chose to leave it as-is.

Saint Augustine, FL

October 6, 2026

Opener motor making abnormal noise on arrival. Attempted limit adjustment and troubleshooting; unit was not repairable. Customer approved replacement. Installed new LiftMaster 1 HP belt-drive opener with new safety sensors and new wall control. Set limits, programmed remote, and tested full operation; door running smoothly.

Saint Augustine, FL

October 5, 2026

Upon arrival, the opener chain was found loose and sagging. Adjusted and tightened the chain to proper tension and tested the door through multiple cycles; it now operates smoothly. Inspected the opener and found no additional issues at this time.

Saint Augustine, FL

October 2, 2026

Customer reported the door would only close fully if the wall button was held down; otherwise it reversed back up. Inspection found failed safety sensors. Customer approved the repair, and we returned to replace the old sensors with new safety sensors and brackets. Tested door operation after install, and the door is in good working order. Customer satisfied with the repair.

Saint Augustine, FL

October 1, 2026

Customer reported cables off and door needing a reset. Reattached both cables, rewound spring, and reset door. Door operating well. Offered new springs and new tracks; customer declined, as he plans to install a commercial-style chain-lift door down the road and only wants the current door working for now. Customer satisfied.

Saint Augustine, FL

September 30, 2026

Customer requested repairs on doors #101 and #110. Both doors had cables off track and off the pulleys. Door #101 also had a roller out of the track and a damaged lock, which we repaired. We fully reset both doors, tightened both tracks, and reset and re-tensioned the cables. Both doors are now working properly.

Jacksonville, FL

September 29, 2026

Customer reported the J-arm had pulled away from the door. With customer approval, tech repositioned the J-arm bracket and secured it with new bolts into a fresh, solid section of the door to ensure a secure hold. Door was tested through multiple open/close cycles and is operating normally. Customer satisfied with the repair.

Palm Coast, FL

September 28, 2026

Completed $123 WAGS Plan 16-point inspection and lubrication. Double door is paired with a low-HP opener that's undersized for the door; recommended upgrading to a higher-horsepower unit. Customer agrees the current opener struggles to lift the door and is very interested in replacing it at a later date.

Saint Augustine, FL

September 25, 2026

Replaced opener installed from previous day. Before removal, found safety sensor and wall button wires crossed, causing indicator lights to come on but preventing operation. Rewired correctly; opener programmed and operated properly from wall button and sensors. Programmed additional remote and keypad, set up Wi-Fi, and walked customer through all functions.

Saint Johns , FL

September 24, 2026

Installed new LiftMaster 2220L chain-drive opener with new safety sensors, wall button and chain rail; programmed open/close limits and force settings and confirmed proper operation. Installed two sets of nylon rollers and two surge protectors. Performed maintenance and lubrication on both doors and the existing 2009 chain-drive opener (single-car door), greasing rail and motor gears; confirmed proper operation.

Saint Augustine, FL

September 23, 2026

Four-door maintenance visit. Replaced all rollers on every door, 40 in total. Lubricated all rollers and hinges, then checked and tightened the belts on each opener. Post-service test: all four doors open and close smoothly with minimal noise. Customer was satisfied with the results and paid in full by check. Recommend routine maintenance in 12–24 months to keep hardware performing at its best.

Saint Augustine, FL

September 22, 2026

Customer requested a garage door opener replacement upon arrival, as the existing unit was no longer working. Per the customer's request, installed a new 1 HP belt-drive opener with a 7 ft rail. Replaced all rollers for smoother, quieter travel, reset the open and close limits, and ran the door through full cycles to verify operation. Door confirmed in good working order at job completion.

Ponte Vedra, FL

September 21, 2026

Upon arrival, found the customer's TorqueMaster system had a broken spring inside the tube, leaving the door unable to open. After discussing options, the customer requested a torsion conversion. Completed the conversion, performed a full maintenance and safety check, and lubricated all hinges and rollers. Door is operating properly.

Saint Augustine, FL

September 18, 2026

Arrived on site and found one TorqueMaster system failed with broken, cut cables. Customer requested torsion conversions on both garage doors (one single-car, one double-car). Converted both doors from TorqueMaster to standard torsion spring systems, set the opener limits, and confirmed both doors are in good working order. Customer paid by card over the phone.

Saint Augustine, FL

September 17, 2026

Customer requested the 123 Maintenance Plan for both garage doors. Completed safety inspection on both doors, replaced rollers, and lubricated all rollers and hinges. Advised customer the Genie opener is 12 years old, at the typical end of its lifespan, and will likely fail at some point. Customer declined replacement for now but will call us first when it goes. Customer satisfied; paid by card.

Jacksonville, FL

September 16, 2026

Customer reported the garage door was not operating properly. Inspection found the opener belt excessively loose. Tightened belt to proper tension; door tested through multiple full cycles and is operating normally. Advised customer that the opener's jumpy, bouncing movement is caused by the sectional (pieced-together) rail rather than a one-piece rail, which allows slight flex during travel.

Saint Augustine, FL

September 15, 2026

Our tech arrived at Dan's Saint Augustine home to find a broken spring keeping his garage door grounded. After a quick estimate, Dan gave us the green light — we swapped in our Forever Springs, and the door is back to working perfectly. Dan's happy, and that's the WagMore way.

Jacksonville, FL

September 14, 2026

Beatriz in Jacksonville is breathing easy — and staying dry! We installed a brand-new weather seal on her garage door, sealing out the Florida heat, humidity, and those surprise afternoon downpours. She's thrilled with the results, and honestly? So are we. That's the WagMore way.

Saint Augustine, FL

September 11, 2026

Upon arrival, we identified an internal wire break affecting the safety sensors. We walked the customer through two options — repair the existing wiring or replace the sensors entirely — and he approved the replacement. We removed the old sensors, cut out the damaged wire, and installed two new LiftMaster safety sensors with fresh wire connections. The door was tested thoroughly to confirm proper operation.

Saint Augustine, FL

September 10, 2026

Installed a Lincoln 1000 (16×7) for Halley in St. Augustine — her new door is looking great! We'll be back tomorrow to complete the project with opener installation. Ready to button it all up and get that door running the WagMore way. 

Jacksonville, FL

September 9, 2026

Customer reported intermittent reversal mid-cycle. Inspection revealed loose sensor wires; reconnected. With customer approval, performed 16-point maintenance: lubricated all hardware, replaced rollers. Door operating properly. Customer satisfied.

Awards and Affiliations

Amarr IDEA EvergreenBBB Accredited BusinessWagmore locally owned and operated certificationClopay LiftMaster
Garage Door Problems?
We turn "Uh-Oh" into "ALL GOOD"

Is your garage door acting up? Don't worry, we've got you covered! Our expert technicians are here to diagnose and fix any garage door issues you may be experiencing. From broken springs to malfunctioning openers, the most likable techs you will ever meet will handle it all with precision and care.

Call Us: 904-584-4828
Arrow