Recent Jobs For Wagmore Garage Doors

August 26, 2026 | Saint Augustine, FL

Replaced 2 broken T-handle locks with new sets, tested locking/operation. Removed old 2006 springs, installed new ones, set proper tension, confirmed door balance. Replaced all rollers with new 7" stem nylon ball-bearing rollers. Lubricated all moving parts—door now quieter and running smoothly. Walked customer through finished work and demoed new lock ...

August 25, 2026 | Orange Park, FL

Installed 16x7 Northwoods door w/ right-side windows, WP3 wind load rated. LiftMaster side-mount opener w/ alternate mounting bracket, wall button, sensors, 2 remotes, keypad. Old door removed & hauled offsite. New trim installed. Homelink programmed on car. Customer trained on wall button/remote operation. Lifetime warranty on mechanical door components & ...

August 24, 2026 | Ponte Vedra Beach, FL

Completed full maintenance service. Replaced all rollers; lubricated springs, rollers, and hinges throughout. Adjusted and tightened opener chain. Door operation significantly quieter post-service. Customer satisfied with results. Opener motor showing early signs of wear (unusual sound during operation) — estimate provided for replacement unit. Recommend follow-up on opener quote.

August 21, 2026 | Jacksonville Beach, FL

Customer reported opener malfunction on arrival. Inspection revealed a 1999 opener with a broken part. Customer declined repair investment on old unit, opted for full replacement. Installed new LiftMaster 1HP belt-drive opener with new wall mount console and new safety sensors. Garage door fully operational. Customer satisfied with new opener performance ...

August 20, 2026 | Saint Augustine, FL

Replaced belt on LiftMaster belt-drive opener (16x8 overhead vinyl back door). Found belt chewed, missing teeth, and slipped off sprocket, causing miscalibration. Opener dated 2006; springs 2009, tension good. Verified belt part number, customer approved estimate. Installed new belt, set proper tension, reset travel limits. Customer satisfied with completed work. Door and ...

August 19, 2026 | Saint Augustine, FL

Torsion spring conversion — 16x7 Wayne Dalton door, Genie chain drive opener. Removed broken spring system; installed new torsion shaft, two WagMore springs, center bearing, bearing plates, drums, cables, and rollers. Lubricated cables, springs, rollers, and hinges. Customer reviewed and approved completed work. Door and opener confirmed working properly.

August 18, 2026 | Saint Augustine, FL

Removed old opener and installed a new LiftMaster 6580L belt drive with belt rail, sensors, wall button, 2 remotes, and keypad. Cut away dry-rotted bottom seal and installed a new one. Reviewed completed work with customer, who was satisfied. Door and opener confirmed working properly at time of departure.

August 17, 2026 | Jacksonville, FL

Completed spring replacement and full door service. Confirmed correct spring size, installed two new springs onto existing hardware (shaft, bearing plates, cables, drums), added tension, and verified proper balance. Replaced all 10 rollers with nylon precision bearing rollers, lubricated hinges and moving parts, reset opener open/close/force settings, and confirmed ...

August 14, 2026 | Saint Augustine, FL

Installed a new 16x7 Amarr Lincoln LI 1000 garage door — white, long panel, no windows. Removed and hauled off the existing door. Adapted the new door to work with the customer's pre-existing opener. Walked the tenant through the completed installation; they were satisfied with the work. Door and opener confirmed working ...

August 13, 2026 | SAINT AUGUSTINE, FL

Arrived to customer reporting a shaky opener. Discovered a broken torsion spring. Completed Safe & Sound Inspection and presented multiple repair options. Customer completed a full door rebuild. Weighed door and installed correct spring line — new shaft, bearings, springs, cables, drums, and center bearing plate. Set proper spring tension, tested ...

August 12, 2026 | Saint Augustine, FL

Customer reported door reversing before fully closing. Found track misaligned, causing binding against frame, plus overly tight top fixtures adding friction. Customer approved quote. Adjusted bottom brackets to correct track spacing, loosened top fixtures to reduce friction, and tightened opener belt. Reviewed completed work with customer, who was satisfied. Door ...

August 11, 2026 | Ponte Vedra, FL

Completed safety inspection on 16x7 Wayne Dalton door w/ Genie 2028. Customer reported screeching noise, requested roller maintenance. Replaced all 10 rollers (nylon), lubricated hinges/rollers, adjusted operator limits. Found screeching from TorqueMaster spring; customer approved conversion to black springs. Installed new springs, cables, drums, bearings; balanced door, re-tested operator—runs smooth, ...

August 10, 2026 | Jacksonville, FL

Replaced broken spring on 16x7 uninsulated door with LiftMaster chain drive opener. Weighed door to confirm correct spring size. Removed old spring, installed new spring and center bearing. Reset opener travel limits and tightened chain. Reviewed completed work with customer — satisfied with results. Door and opener confirmed working properly at ...

August 7, 2026 | Jacksonville,, FL

Installed LiftMaster 2220L opener on 10x8 steel insulated Amarr door. Customer reported remotes not staying connected — diagnosed as bad receiver on logic board of original 1997 opener. Customer approved replacement estimate. Removed old opener; installed new LiftMaster 2220L with two remotes, wall button, sensors, and keypad. Customer reviewed completed work, satisfied. ...

August 6, 2026 | Jacksonville, FL

Summer maintenance check-up on 16x7 and 8x7 doors, LiftMaster belt drive openers. Removed and replaced rollers with 10 new nylon rollers per door (20 total). Lubricated hinges, rollers, bearings, and springs on both doors. Reset travel limits on both openers. Added spring tension on the 16x7 door. Tightened belts on both openers. ...