Recent Jobs For Wagmore Garage Doors

July 30, 2026 | Jacksonville, FL

16x7 Wayne Dalton door, Genie 2028 opener — TorqueMaster conversion. Customer reported door sticking on initial daily opening; door would stay open only via manual emergency release, then wouldn't hold at full open. Diagnosis: weak TorqueMaster spring + sticky vinyl trim residue. Customer approved TM conversion only (declined trim). Installed new torsion springs, ...

July 29, 2026 | Jacksonville, FL

Completed door reset on 16x7 Clopay insulated door with Genie screwdriver opener. Customer requested top/bottom brackets, two struts, and reset. Installed struts, top fixtures, and bottom brackets before winding springs. Tightened cables into drums, added spring tension, confirmed balance — door operating properly. Opener sensors found failed, preventing down travel. ...

July 28, 2026 | Saint Augustine, FL

Replaced opener on 16x7 Wayne Dalton door. Inspection revealed a bad gear inside the existing Genie opener. Door was already torsion spring converted with nylon rollers. Customer approved estimate for LiftMaster 6580L belt drive opener. Removed old unit; installed new 6580L with remote, sensors, wall button, and keypad. Customer reviewed ...

July 27, 2026 | Middleburg, FL

Installed a 16x7 N. Woods NW 3000 garage door, customer-supplied Chamberlain belt-drive opener retained per customer request. Removed and hauled away the old door, installed new trim around the opening. Walked the customer through the completed work — they were satisfied. Door and opener tested and confirmed working properly at time of ...

July 24, 2026 | Jacksonville, FL

Customer reported the door opening fine but slamming down—inspection found a broken torsion spring. Measured and confirmed matching standard black springs were on the truck. Customer approved estimate; removed both failed springs and installed two new standard black torsion springs. Balanced the door properly, reattached to the operator rail, ...

July 23, 2026 | Saint Augustine, FL

Installed LiftMaster 8500W... wait, let me match this correctly — LiftMaster 6690L belt drive opener on 16x7 overhead door as part of summer ready check-up. Removed old opener; installed new unit with sensors, wall button, two remotes, and keypad. Replaced all 10 rollers. Adjusted spring tension. Lubricated hinges, rollers, springs, bearings, and ...

July 22, 2026 | Nocatee, FL

16x7 Wayne Dalton opener replacement. Customer reported opener failure following an electrical storm. Inspection revealed a bad circuit board. Estimate approved for new LiftMaster 6690L belt drive opener. Removed old unit; installed new opener with sensors, wall button, two remotes, and keypad. Customer reviewed and approved completed work. Door and ...

July 21, 2026 | Nocatee, FL

Installed two LiftMaster 6690 belt drive openers with 7' rails and a new torsion spring system (shaft, bearings, plates, cables, drums) on a single-car door. Balanced the door, mounted openers on existing angle iron, programmed settings/remotes/keypads. Lubricated all moving parts, cleaned up, and reviewed operation/emergency release with customer. ...

July 20, 2026 | Saint Augustine, FL

Performed full maintenance, dent repair, and bottom seal replacement on a 16x7 Wayne Dalton door with Genie 2028 opener. Repaired panel dent, removed old bottom seal and installed new seal with retainer, lubricated springs, rollers, cables, bearings, and hinges. Tightened opener chain and added spring tension. Relocated sensors lower to clear ...

July 17, 2026 | Saint Augustine, FL

Customer's Genie chain-drive opener wasn't operating; door was extremely heavy on manual release. Diagnosed a broken TorqueMaster spring. Customer approved conversion to standard torsion system. Removed failed TorqueMaster components; installed new torsion springs, cables, drums, bearings, bearing plates, and shaft. Tensioned springs, confirmed proper door balance, and lubricated all new ...

July 16, 2026 | Jacksonville, FL

Completed LiftMaster 98022 side-mount opener install w/ MyQ video keypad. Disabled power, removed failed opener, mounted new motor to spring shaft, wired sensors, wall button, and auto slide lock. Restored power, set open/close limits, programmed remotes—all tested working. Helped customer set up MyQ app for opener/keypad, confirmed function. ...

July 15, 2026 | Saint Augustine, FL

Replaced two broken springs and cables on a 16x7 uninsulated door, plus full maintenance/lube, with linear chain drive opener. Customer reported broken springs, opener issues, and cable concerns. Estimate signed; springs/cables replaced, balance confirmed, all moving parts lubricated. On first opener test, tensioning bolt snapped (pre-existing spring-break damage) — ...

July 14, 2026 | Saint Augustine, FL

16x7 Wayne Dalton door — customer reported door was sketchy/needed work. Inspection found noisy TorqueMaster spring causing heavy imbalance; opener (Genie, 10+ yrs) had stretched belt, missing nylon washers. Customer approved torsion conversion + belt drive opener. Converted to Forever Springs w/ center bearing, plates, cables, drums, shaft (door weighed for proper ...

July 13, 2026 | Jacksonville, FL

Arrived to failed torsion springs; customer had signed estimate for replacement. Measured door and confirmed correct spring size needed. Removed failed springs, installed two new .25 x 30" springs with steel center bearing. Lubricated springs, tested door balance and operation. Reset open/close limits on operator, confirmed proper function with and without ...

July 10, 2026 | Jacksonville, FL

Customer reported door would not open. Inspected 16x7 overhead door with Genie belt drive opener and found a broken spring. Customer approved estimate for single spring replacement. Removed old spring, weighed door to confirm correct new spring size, installed new spring, and adjusted to proper tension. Customer reviewed completed work ...