Recent Jobs For Wagmore Garage Doors

July 15, 2026 | Saint Augustine, FL

Replaced two broken springs and cables on a 16x7 uninsulated door, plus full maintenance/lube, with linear chain drive opener. Customer reported broken springs, opener issues, and cable concerns. Estimate signed; springs/cables replaced, balance confirmed, all moving parts lubricated. On first opener test, tensioning bolt snapped (pre-existing spring-break damage) — ...

July 14, 2026 | Saint Augustine, FL

16x7 Wayne Dalton door — customer reported door was sketchy/needed work. Inspection found noisy TorqueMaster spring causing heavy imbalance; opener (Genie, 10+ yrs) had stretched belt, missing nylon washers. Customer approved torsion conversion + belt drive opener. Converted to Forever Springs w/ center bearing, plates, cables, drums, shaft (door weighed for proper ...

July 13, 2026 | Jacksonville, FL

Arrived to failed torsion springs; customer had signed estimate for replacement. Measured door and confirmed correct spring size needed. Removed failed springs, installed two new .25 x 30" springs with steel center bearing. Lubricated springs, tested door balance and operation. Reset open/close limits on operator, confirmed proper function with and without ...

July 10, 2026 | Jacksonville, FL

Customer reported door would not open. Inspected 16x7 overhead door with Genie belt drive opener and found a broken spring. Customer approved estimate for single spring replacement. Removed old spring, weighed door to confirm correct new spring size, installed new spring, and adjusted to proper tension. Customer reviewed completed work ...

July 9, 2026 | Jacksonville, FL

Customer heard loud noise, reported broken spring on 16x7 overhead door with LiftMaster belt drive opener. Confirmed broken spring on inspection. Customer approved estimate. Removed two broken springs, installed two Forever Springs with new cables, and installed 10 new rollers. Lifetime warranty on springs, cables, and rollers applies with annual WagMore ...

July 8, 2026 | Ponte Vedra, FL

Installed new LiftMaster 6690L belt drive opener with 2 remotes and keypad. Removed old opener; installed new rail, motor, sensors, wall button, and keypad. Programmed remotes, set open/close limits, and tested thoroughly. Completed full door maintenance/lubrication and replaced all rollers with new quiet nylon rollers. Connected opener to customer's ...

July 7, 2026 | Saint Augustine, FL

Completed TorqueMaster-to-standard torsion conversion on a 16x7 Wayne Dalton double door. Door was too heavy to lift manually; opener could close but not open it — classic broken spring symptoms. Installed new springs, shaft, bearing plates, cables, and drums. Balanced door, reset opener limits and force settings. Fully operational.

July 6, 2026 | Jacksonville, FL

Completed installation of two new hinges. Removed existing #2 and #3 hinges, installed new powder-coated #2 and #3 hinges using existing rollers. Replaced all screws with new longer self-tapping screws. Tested door multiple times to confirm panels no longer popping. Ran door with customer.

July 3, 2026 | Ponte Vedra, FL

Completed install of LiftMaster 6690L belt drive opener. Removed failed unit, installed new opener, belt rail, wall button, and sensors, adapting to existing wiring. Programmed open/close force settings, 3 handheld remotes, and 1 keypad. Demoed operation for customer and assisted with Wi-Fi connection setup. Job complete, customer walked through full functionality.

July 2, 2026 | Jacksonville, FL

Customer reported detached opener rail pin (no cotter pin found) and sensor misalignment error. Reinstalled slide/pin with new cotter pin. Diagnosed sensors: alignment and wiring confirmed good, but door still errored without sunlight interference — sensors had failed. Temp-tested new LiftMaster sensors, confirmed fix, customer approved replacement. Fully installed new ...

July 1, 2026 | Anaverde, FL

Completed spring replacement on a 16x8 insulated door. Removed tension from both the broken and intact springs, then replaced both with new powder-coated WagMore springs. Re-tensioned to properly lift door weight and confirmed smooth operation. Installed a new operator bracket (old one ripped off when spring broke), reattached operator, reset ...

June 30, 2026 | Palm Cost, FL

Installed 16x7 Amarr Lincoln LI 3000 steel back insulated door, WP5 wind load rated, w/ LiftMaster 6690 belt drive opener. Removed old wood door & opener, hauled off site. Lifetime warranty on all door mechanical components; lifetime motor/belt warranty on opener. Opener functioning properly.

June 29, 2026 | Jacksonville, FL

Reset crooked 16x7 uninsulated door; cable had jumped shaft instead of drum. Backwound springs, lowered door, removed tension, found incorrect cables causing pop-off. Customer approved replacing with correct cables. Re-tensioned springs, cycled door multiple times to confirm smooth operation. Also realigned sensors on customer-installed Chamberlain belt drive opener for proper ...

June 26, 2026 | Jacksonville, FL

LiftMaster 6690L belt drive opener installed. LiftMaster 6690L belt drive opener installed. Customer's 2015 Craftsman had been on emergency release 1+ yr — motor attempted to start but stopped; damaged plastic sprocket found. Logic board replacement estimated; customer chose full replacement. Removed old unit, installed new rail/motor on existing angle iron, reused ...

June 25, 2026 | Saint Augustine, FL

St. Augustine homeowner Stan called us with a garage door that was grinding and completely inoperable — what looked like one problem turned out to be a chain reaction. A failed TorqueMaster spring made his Wayne Dalton so heavy that every lift attempt destroyed the belt, sprocket, and pulley on the ...