Adam Stanton

Completed S&S Inspection on 16x7 uninsulated door w/ Chamberlain chain drive (2023). Found loose chain, fatigued springs, and zero maintenance since install. Performed full lube & maintenance—rollers, hinges, bearings, cables, drums, springs. Adjusted spring tension, tightened chain, reset force/travel limits. Pre-existing bent rail noted to homeowner. Door operating quietly and correctly at close.

Thomas in Saint Augustine got our $0 Safe & Sound Inspection on both garage doors — a 16x7 (2012 Chamberlain belt-drive) and a 9x7 (2003 LiftMaster). During the inspection, we found the Chamberlain's drive belt was destroyed with missing teeth, causing the door to lock up. We also lubricated and serviced both systems, and flagged some wear on the original 2003 spring and double-door cables for down the road.

Jacksonville neighbor Robert's garage door suddenly wouldn't budge — turned out to be a snapped spring, one of the most common (and misunderstood) door issues out there. Our $0 Safe & Sound Inspection confirmed it, and we walked Robert through exactly what was needed. No guesswork, no upsells — just an honest fix that got his door back up and running.

Performed maintenance, roller replacement, and bottom seal replacement on a 16x8 uninsulated door with LiftMaster opener. Customer reported noise and a hanging bottom seal. Inspection found opener as primary noise source, with clicking rollers; old bottom seal cracked. Replaced bottom seal, installed 12 new rollers, lubricated rollers/hinges/springs. Door and opener functioning properly.

Completed Safe & Sound Inspection on a 16x7 uninsulated door with a linear chain drive opener. New homeowner had concerns about a previously repaired emergency release. Springs (2014) were balancing properly but aging. Found 10 rollers dragging, causing friction noise. Customer approved free roller maintenance promo: installed new nylon ball-bearing rollers, lubricated springs/hinges, greased rail, tightened chain. Tested—everything working properly.

Provided estimates for one new garage doors on inherited property with original, aging doors. One door's opener functions; the other doesn't. Customer requested pricing for single door now, second later. Took measurements/photos. Structural upgrades needed: spring pad, added jamb bracket wood. Existing opener was hot-wired into a light fixture with no receptacle—new receptacle required for replacement opener.

Diagnosed longstanding open/close issues on 2005 opener. Found incorrect aftermarket sensors and improperly set force limits; door weight tested well above manufacturer spec, with aging 2014 springs. Reviewed findings with customer, who opted to replace sensors and recalibrate force limits now, with spring replacement and new opener planned for next month. Installed new LiftMaster sensors, reset force limits, and confirmed smooth, reliable operation.

Replaced opener on 16x8 vinyl insulated door for intermittent stopping. Inspection confirmed opener malfunction and undersized springs causing improper door balance. Customer approved opener replacement quote. Installed LiftMaster 6580L with 8' belt rail, safety sensors, wall button, and 1 remote. Covered by 6-year motor/belt warranty and 5-year labor warranty.

Performed maintenance on a 16x7 uninsulated door with a Craftsman chain drive opener. Customer reported the wall button had to be held to operate the door. Inspection revealed a loose connection at the left safety sensor, causing intermittent operation; holding the wall button overrides sensor inputs, which masked the underlying issue. Reconnected and secured the sensor wiring to restore normal automatic operation.

16x7 non-insulated door reset w/ linear chain drive opener. Arrived to find cable and bottom bracket removed, door severely crooked from vehicle impact. Reset cables/drums, replaced bottom bracket screws, unbent left track, installed flag screws, re-tensioned springs, confirmed balance. Removed partial dents from damaged bottom panel. Reset open/close limits.

Arrived to find broken spring. Removed failed springs, weighed door, confirmed and installed correct replacement springs. Verified balance. Replaced all rollers with nylon. Completed full maintenance and lubrication on door and opener. Reset open/close limits, and tested operation.

Performed maintenance on 16x7 Wayne Dalton door with Genie 2028 chain drive opener. Corrected improper top bracket installation causing side gap. Lubricated hinges, rollers, cables, and bearings. Door has TorqueMaster spring system — balance.

Door reset & cable replacement. Door reset & cable replacement. Found door crooked with one cable off — customer reported opener hadn't worked since move-in 4 months ago. Replaced both cables, reset drums, rebalanced door. Realigned safety sensors and reset opener limits — now fully operational. Lubed springs, rollers, hinges; greased rail; tightened chain.

Arrived to find a broken TorqueMaster spring on a 16x8 Wayne Dalton insulated door — opener unable to lift. Completed full torsion spring conversion: installed new spring line, bearing plates, center bearing, springs, drums, and cables. Balanced door, lubricated all components, reset open/close limits, and adjusted chain tension on Genie chain drive opener. Door tested and operating properly.

Installed new LiftMaster 6690L belt drive opener. Removed failed unit; replaced angle iron with professional-grade, adapted existing wiring. Replaced sensors, wall button, keypad, J-arm, brackets, motor, and belt rail. Programmed open/close limits, force settings, both remotes, and keypad to customer's code. Lubricated all hinges, rollers, and springs due to excessive noise.

Replaced double torsion springs (powder-coated), worn metal rollers w/ nylon sealed ball bearing rollers, and failed opener w/ new 1HP belt drive unit on 16x7 vinyl-back insulated door. Door weighed for proper spring sizing. Full lubrication of springs, rollers, hinges, cables & bearings. Per customer-approved Safe & Sound quote.

Performed Safe & Sound Inspection on 8x7 steel-back insulated door. Performed Safe & Sound Inspection on 8x7 steel-back insulated door. Customer reported intermittent wall button. Found loose wire at opener; reconnected and tested. One sensor light out but functional. Springs dated 2019, balanced. Nylon rollers good. Lubed springs, rollers, bearings, hinges & cables. Door and opener operating properly.

Performed Safe & Sound Inspections on two steel-back insulated doors (16x7 and 8x7). Customer reported a broken spring on the 16x7 door, which was confirmed during inspection. Door was weighed to verify spring sizing — existing springs were correctly sized for the door weight. J-arm was also found to be bent. Replaced both torsion springs on the 16x7 door, installed new rollers on both doors, and completed full maintenance/lubrication on both doors. J-arm addressed. Both doors operating correctly upon completion.

Installed heavy-duty adjustable operator bracket on 16x7 overhead door. Customer reported door falling while traveling. Found loose operator bracket, slightly loose chain, dry hinges, and worn rollers. Springs (2018) balanced well. Tightened chain, lubricated hinges, rollers, cables, bearings & springs. Opener operating properly. Lifetime parts & labor warranty on bracket with annual WagMore service.

A Saint Augustine homeowner called us when their garage door sensor stopped working — and our inspection turned up more than just a loose wire. We reconnected the safety sensors, corrected the spring tension, lubricated all the moving parts, and programmed the keypad, leaving the door and LiftMaster opener running perfectly. That's Wagmore.

Replaced both snapped torsion springs on a 16x7 uninsulated door with Lanier chain drive opener. Replaced both snapped torsion springs on a 16x7 uninsulated door with Lanier chain drive opener. Installed new center bearing and bearing plate, set drums, and tensioned springs to spec. Reconnected disconnected cable. Lubricated all moving parts and adjusted opener travel limits and force settings. Door tested and confirmed operating correctly.

A Yulee homeowner upgrading to a mini-split needed their 16x7 garage door insulated for climate efficiency — but the added weight meant the existing springs had to go too. Wagmore installed a full vinyl back insulation kit, custom-cut around the top panel windows, then weighed the door and replaced both torsion springs with correctly-sized hardware for a properly balanced result. That's Wagmore.

A snapped TorqueMaster spring had this Saint Augustine homeowner's Wayne Dalton door completely out of commission — and during our inspection, we confirmed the rest of the door and Genie opener were in great shape. We removed the failed TorqueMaster system and converted it to a dual torsion spring setup with a new shaft, bearings, drums, cables, and two powder-coated springs, leaving the door fully operational and built to last. That's Wagmore.

Customer reported having to assist lifting the door while the opener ran. Inspection revealed a failed coupler in the screw drive opener. Springs dated 2019 with good balance; hinges noted dry. Findings presented to customer; coupler replacement approved. Dismounted opener, removed broken coupler, installed new coupler, re-mounted opener, adjusted limits, and verified operation. Door and opener functioning properly.

S&S Inspection found bent bottom brackets (roller pop-out), fraying cables, improper drums, and heavy spring. S&S Inspection found bent bottom brackets (roller pop-out), fraying cables, improper drums, and heavy spring. Reviewed findings w/customer; recommended bottom fixture & cable replacement alongside maintenance. Released tension; removed old cables & brackets. Installed powder-coated brackets & 7' torsion cables. Restored tension, confirmed balance. Replaced rollers, lubed all components, tightened chain, greased rail, reset limits. Door runs smooth & quiet. Customer satisfied.

Replaced bottom seals on (1) 16x7 & (1) 8x7 Wayne Dalton. Replaced bottom seals on (1) 16x7 & (1) 8x7 Wayne Dalton. Removed old seals, adjusted silver retainers, lubricated & installed new Wayne Norton rubber, trimmed ends, reset open/close limits. Full maintenance performed — lubed hinges, rollers, springs, bearings, cable drums & operator rails; tightened belts. Both doors quieter & smoother.

Dual Door Maintenance – 16x7 & 8x7 Clopay Uninsulated | LiftMaster Chain Drive Customer reported both doors noisy and never serviced. Inspection revealed dry hinges (primary noise source), springs dated 2021, heavy spring balance on double door, and loose opener chain. Performed full maintenance on both doors: adjusted torsion spring tension, tightened chain drive, and lubricated springs, rollers, cables, hinges, and bearings. Customer reviewed completed work and was satisfied.

Installed T-handle exterior lock on 8'9" x 6'3" CloPay uninsulated door. Customer reported lock had seized due to salt air corrosion. Inspection 5/11 confirmed seizure; customer approved estimate same day and lock was ordered. Returned 5/14 to complete replacement. Removed corroded lock, installed new T-handle. Door operating properly. Customer satisfied.

16x7 Wayne Dalton | Genie 2028 Belt Drive Performed full maintenance. Springs dated 2018, balanced and in good condition — added ¼ turn to one spring for preventive fatigue compensation. Belt drive slightly loose; tightened. Nylon rollers previously installed. Lubricated hinges, rollers, springs, cables, and drums. Cleaned bottom seal. Door and opener operating properly. Customer reviewed completed work and approved.

Broken spring replaced w/ single larger spring (lifetime warranty w/ biennial WagMore service). Bottom seal dry-rotted, intact. Door 2: Bottom seal torn/missing pieces — replaced (1-yr parts & labor warranty). Spring rusty, likely original. Both doors: rollers worn/noisy. Work completed. Both doors & openers functioning properly. Customer satisfied.

Maint & lube on 16x7 non-insulated door w/ original Wayne Dalton chain drive. Replaced all rollers w/ nylon whisper-quiet. Springs ~10 yrs old — added tension, reweighed to 8–10 lbs. Lubed hinges, bearings, cable drums & springs. Tightened chain. Sensors & remotes functional. Educated customer on future opener replacement options.

16x7 uninsulated door w/ Linear Chain Drive. Customer reported door not working & loud grinding noise. Inspection revealed broken spring — both original to house (2003). Quoted & approved double spring replacement. Weighed door, selected proper springs, removed old hardware & installed two powder coated forever springs, wound to proper tension. Door & opener operating properly.  Lifetime warranty on springs w/ biennial WagMore service.

Performed maintenance on 16x7 vinyl back insulated door with Genie chain drive opener. Lubricated all rollers, hinges, and springs — door now runs quietly and smoothly. Confirmed proper door balance; springs (installed 2024) required no tension adjustment. Tightened opener chain and reset travel limits.

Performed $0 Safe & Sound Inspection on 16x7 overhead door with Genie screw drive opener. Found multiple hinges pulled from stiles on left side and one center hinge pulled out. Spring balance slightly heavy. Removed failed hinges, installed two new powder-coated hinges, powder-coated top fixture, and reinforced the stile.

Performed Safe & Sound Inspection on 16x7 Wayne Dalton Torque Master w/ LiftMaster chain drive. Performed Safe & Sound Inspection on 16x7 Wayne Dalton Torque Master w/ LiftMaster chain drive. Found broken torque master spring, dry rollers/hinges, misadjusted limits & low chain. Completed torque master conversion: new cables, bearing plates, center bearing, drums & powder-coated springs (lifetime warranty). Adjusted tension, reset limits, tightened chain & lubricated all moving parts.

A Saint Johns homeowner's Wags Family Plan visit covered full lubrication, spring and limit adjustments, and chain tension — the kind of proactive care that keeps garage doors running safely and quietly for the long haul. Book your $0 Safe & Sound Inspection! That's Wagmore.

Caleb, a Jacksonville homeowner called us about a grinding noise after their door ran down on an object — turns out a disconnected wire, misadjusted limits, and a bent J-arm were all working against them. We reconnected, reset, and replaced what was needed, and their Chamberlain Whisper Drive is running smoothly again. Book your $0 Safe & Sound Inspection today! That's Wagmore.

A Jacksonville homeowner's failing Chamberlain opener was swapped out for a new LiftMaster 6580L belt drive — complete with new rail, sensors, keypad, wall button, and a full myQ smart phone setup. The new opener is backed by a 6-year LiftMaster motor and belt warranty plus a 5-year Wagmore labor warranty. That's Wagmore.

A free Safe & Sound Inspection on a Saint Augustine home's Amarr door turned up 26-year-old springs, worn rollers, and a dry-rotted bottom seal — all flagged, all documented. The door and opener are working for now, but we'll be ready when the customer is.Signed up for our Wags Plam. That's Wagmore.

A Saint Augustine homeowner couldn't get their door to open more than a few feet — turns out the up limit on their LiftMaster screw drive opener had maxed out and needed to be manually taken apart and reset. We corrected the limits, programmed a new remote, and had the door operating at full range before we left. That's Wagmore. Book your $0 Safe & Sound Inspection today!

Two Wayne Dalton Torque Master doors in Saint Johns got the full treatment — new bottom seals, whisper-quiet nylon roller upgrades, full lubrication, and opener limit resets on both. The homeowner signed up for the Wags Family Plan and walked away with two doors running like new. Book your $0 Safe & Sound Inspection — That's Wagmore.

Two-sentence version: A St. Augustine homeowner reached out wanting new rollers on his garage door — our free Safe & Sound Inspection revealed dry hinges, noisy rollers that had never been lubricated, and a door that felt heavy due to low spring tension. We replaced all 10 rollers with precision bearing nylon rollers, lubricated every moving part, and re-tensioned the springs, leaving him with a door that's quieter, lighter, and balanced. That's Wagmore.

Two-sentence version: A Nocatee homeowner woke up to a broken spring and a door that wasn't going anywhere — we came out, replaced both springs and the center bearing on their Wayne Dalton, and had everything running smoothly again. Every spring we install comes with a lifetime warranty, as long as the door is serviced by Wagmore every two years. Think your springs might be on their way out? Book your $0 Safe & Sound Inspection today! That's Wagmore.

We just completed a new construction garage door installation in Hastings — a beautiful Amarr Lincoln LI 3000 insulated steel door in almond with short panel windows, built to Florida's WP5 wind load standard. This door comes with a lifetime warranty on all mechanical components, and we're proud to be the team keeping it protected for years to come. Book your $0 Safe & Sound Inspection today! That's Wagmore.

This Jacksonville home got a full fresh start — complete removal of the old door and opener, followed by a new non-insulated 16x7 installation with all-new panels, track, hardware, springs, and a LiftMaster 2220L chain drive opener, all balanced, programmed, and lubricated before we left. The new door comes with a lifetime parts and labor warranty on all components, as long as Wagmore performs maintenance at least once every two years. That's Wagmore.

When this East Palatka homeowner's Amarr door came off track, our $0 Safe & Sound Inspection revealed tangled cables, displaced rollers, a folded bottom panel, and a bent LiftMaster trolley — damage that's easy to miss without a trained eye. The full reset and trolley replacement are underway, and this door will be back to safe, reliable operation before the week is out. That's Wagmore.

Performed a torsion spring conversion on a 9 x 7 wood door with a genie screw drive opener. During my inspection, I confirmed that one of the extension springs were broken. I removed the old extension spring system, and installed a new bearings, plates, drums, cables, shaft, and springs. The torn spring has been sized properly to the weight of the door and balance tested. Door opener working properly at this time.

John in Jacksonville reports his two-car garage door system is operating inconsistently — the door and opener fail to complete cycles reliably. Observed issues include the door initiating descent then stopping mid-travel, as well as failing to remain in the closed position after closing. Customer is requesting a full inspection, diagnosis, and repair. Customer is enrolled in the Wags Family Plan.

Clifton's garage door had stopped responding to the remote entirely — no electronic open, no electronic close, manual operation only. Our tech reprogrammed the remote to the opener during a $0 Safe & Sound Inspection, and the door was back to full automatic operation before he left. That's Wagmore.

Technician replaced all hinges and installed 12 ultra-quiet rollers on a double-car 8-foot door, lubricating all hardware upon installation. Full maintenance was performed on both doors and openers, including spring tension adjustment, opener limit reset, and Genie motor chain tightening. Upon completion, the door was cycled multiple times — customer observed and confirmed a dramatic reduction in noise. A universal wireless Genie keypad was installed and programmed to the customer's preferred code, with operation confirmed before technician departure.

Upon arrival, the customer reported concerns about door safety and that the door wouldn't open fully, preventing him from parking inside. Inspection revealed several issues including improperly set opener limits, a sagging chain, worn sprocket gears, fraying cables, aged 2012 springs causing a heavy door, and lack of lubrication throughout. Customer approved a full rebuild and opener replacement — technician installed .207 springs with new hardware, nylon rollers, two hinges, and a LiftMaster 2220L chain drive opener with remote and keypad, then balanced the door, programmed all controls, and walked the homeowner through operation.

Technician inspected a 16x7 Wayne Dalton door and confirmed a broken opener chain and a failed Torque Master spring, with the spring failure identified as the likely cause of the chain break. Multiple failed components — including an opener that would only run in the down direction — made replacement the only advisable course of action, which the customer approved.

This Saint Augustine garage door needed a complete refresh — worn bottom seal, failing springs, and frayed cables were all working against it. Our $0 Safe & Sound Inspection identified every issue and we knocked it all out in one visit with a double spring replacement, new cables, and a fresh bottom seal. That's Wagmore.

Cstomer stated that garage door was not working. Performed $0 Diagnostic Inspection on a 16x7 Overhead Door with OHD opener. Found one broken spring and a broken operator bracket. Completed an double spring replacement and adjustable operator bracket.

Single Spring Replacement -9x8 Vinyl Back Insulated Door - LiftMaster Belt Drive Opener. Broken torsion spring found on inspection. Installed new spring and center bearing. Corrected opener limits, swapped sensors to prevent sun interference, re-spliced wiring. Lubricated all moving parts. Door and opener operating correctly. Customer satisfied. 

Returning customer Kevin, requested opener replacement due to noise post-rebuild. Opener damage from broken spring operation noted/declined at prior visit. Installed LiftMaster 2220-L w/ sensors, wall button, remote, existing wiring. Programmed limits, lubed rail, vehicle, MyQ app.

Safe & Sound Inspection on two 8x8 uninsulated Clopay doors with Genie 2028 openers. Customer reported one door not opening and both doors noisy. Found corroded sensor terminals on door 2 and dry hinges with metal shavings on both doors. Completed two maintenances and sensor replacement. Replaced both sensors on door 2, lubed hinges/rollers/springs/bearings/cables on both doors, tightened chains on both openers. Doors and openers operating properly at completion.

Customer attempted DIY bottom seal replacement but couldn't find compatible rubber for the older door. Confirmed our retainer would fit, presented estimate, customer approved. Removed old retainer and installed new aluminum retainer and T-channel track. Lubricated track and installed new seal rubber. Reset opener travel limits and confirmed no light gap in closed position.

Arrived to customer reporting a shaky opener. Discovered a broken torsion spring. Completed Safe & Sound Inspection and presented multiple repair options. Customer completed a full door rebuild. Weighed door and installed correct spring line — new shaft, bearings, springs, cables, drums, and center bearing plate. Set proper spring tension, tested operation, lubricated all new parts, reset opener travel limits, and tightened opener chain.

Installed two new 8x7 non-insulated doors. Removed both existing doors and installed all new hardware — tracks, springs, and panels. Adjusted springs to proper tension and confirmed both doors operating correctly. Installed outdoor side trim on both doors; customer was very happy.

After 20 years of wear, their garage door finally gave out — stuck, noisy, and done for good. They called WagMore and we took care of everything. New door, new quiet LiftMaster opener, and a smooth install from start to finish. No stress, just results. Now they're rolling in and out like it's brand new — because it is!

Transparent and trust-building: Jacksonville Beach homeowners — sometimes a garage door problem runs deeper than it first appears. When our technician arrived, the homeowner's door had stopped working and the left cable had come off. Inspection revealed a bent track and a loose wall bracket — not a simple fix. We reset the door, reset both drums, re-tensioned the springs, straightened the track bracket, and drilled a new lag to secure it to the wall. We got the customer's car out safely. That's what honest service looks like — we don't close a job until it's right. That's Wagmore.

Nocatee homeowners—a noisy 16x7 Wayne Dalton brought us out for a Safe & Sound Inspection, and we replaced all plastic rollers with 2" nylon rollers, lubricated the hinges, cables, and drums, tightened the chain on the Genie opener, and reset the force limits. The door is running significantly quieter — and we've flagged the Torque Master spring for the homeowner to keep on their radar. That's Wagmore.

A door that stops a few inches off the ground and fights you on the way down is a broken Torque Master spring, and it only gets worse. We completed a full conversion: new shaft, springs, bearings, drums, cables, and bearing plates — lubed, limits reset, and running like it should. That's Wagmore.

Performed Safe & Sound Inspection on a 9x7 uninsulated door (no opener). Customer requested opener and keypad installation. Inspection revealed a 1999 torsion spring with heavy rust and worn/rusty rollers. Installed a basic opener with keypad, spring replacement, and roller replacement. Completed torsion spring replacement, center bearing, and 10 rollers.

Customer reported door opening ~1 ft before struggling and reversing. Found fatigued Torque Master spring — not yet broken but extremely heavy. Customer approved full conversion. Installed new bearing plates, center bearing, spring, drums, shaft, and lift cables. Tensioned to spec, reset opener limits, tested door and operator — both functioning properly. Lubricated all moving components.

On this call, our tech removed the existing opener and extension spring system, weighed the door, and spec'd the right torsion spring for the job — a .207 gauge single spring. From there it was a full build: new cables, bearing plates, spring pad, center bearing, and a properly tensioned and balanced torsion spring. Then came the new LiftMaster 2220L chain drive opener — installed, programmed, and confirmed working before we left. Every moving part got lubed: springs, drums, rollers, hinges, rail, and bearings. Door and operator are running strong.

Orange Park homeowners — when your double garage door stops working, the answer isn't always a repair. Sometimes a fresh start is the smarter move. That's exactly where Bill found himself — double door down, car stuck outside, and ready for a real solution. Our tech came out, assessed the situation, walked him through his options, and put together a quote for a full replacement. A new door and opener are already on order, and Bill will be back in his garage before long. If your door is giving you trouble, don't wait it out. Book your $0 Safe & Sound Inspection today and let's figure out the right next step for you.

When our tech arrived, the homeowner explained that rodents had chewed through his existing seal — and the damage was significant enough that a simple swap wasn't an option. The old seal wouldn't accommodate a standard aftermarket replacement, so we installed a new retainer along with fresh rubber, ran the door to confirm it seated properly, and left the bottom of that door tight and protected. Our tech also walked the homeowner through rodent-resistant seal options for future consideration — because knowing your choices matters, even if you're not ready to act on them today. A compromised bottom seal is an open invitation.

Safe & Sound Inspection – 16x7 Wayne Dalton / TorqueMaster Customer reported backing into the door. Inspection revealed a bowed bottom section and strut (cosmetic, not affecting operation), fatiguing TorqueMaster spring causing heavy door balance, and loose/crooked hinges. Customer signed up for Wags Family Plan. Straightened and tightened all hinges; lubricated hinges, rollers, cables, and drums. 

Jacksonville Beach homeowners—our $0 Safe & Sound Inspection on an 8x7 door with a Chamberlain chain drive uncovered a faulty sensor, a non-communicating keypad, and old extension springs running without safety cables. Our tech completed a torsion spring conversion, resolved every issue found, and left the door and opener fully operational. That's Wagmore.

Afull door replacement is a big deal, and every detail matters. Our team removed the old door, installed a new Amarr Lincoln LI 1000 with fresh white outdoor trim, adapted the existing opener with a new bracket, reset limits, and reinstalled safety sensors to proper code height—leaving the site clean and the door running right. That's Wagmore.

Our tech arrived to a 16x7 non-insulated CHI door and got to work. A quiet door kit was installed, bringing down the noise and smoothing out the operation. From there, a full maintenance was performed—wire connections were redone, and hinges, springs, and rollers were all lubricated. Before leaving, the door and opener were confirmed working properly.

Service Summary – Torsion Spring Replacement & Tune-Up Confirmed proper spring sizing on arrival. Removed failed torsion springs and installed two new lifetime torsion springs and center bearing. Tested and balanced door. Performed full tune-up: lubricated hinges, rollers, bearings, and springs, greased opener rail, reset open/close and force limits. Adjusted top fixtures to eliminate light gap on top panel. Homeowner confirmed satisfaction with door operation.

Service Summary – Panel Repair & Reinforcement Customer reported top section separating from the intermediate section with hinges ripped out. Performed temporary repair and reinforcement: removed and realigned top row of hinges, reinstalled and reinforced roller mounting edges on both sections. Realigned tracks. Lubricated rollers, hinges, cables, and drums. Door and opener operating properly at this time.

Failed Torque Master spring causing binding through radius. 16x7, Genie 2028 Chain Drive, installed 2018. Conversion to torsion springs completed: removed TM assembly, installed bearing plates, center bearing, cables, springs, drums & shaft. Reset opener limits, tested operation. Door operating smoothly. 1-yr maintenance approved.

Completed Safe & Sound Inspection on 16x8 Wayne Dalton with Torque Master spring system and Genie 2028 opener. Elizabeth reported broken springs — confirmed on inspection. Also noted dry hinges and loose chain. Completed a torsion spring conversion and lubricated hinges, springs, rollers, bearings, and drums; adjusted chain tension. Door and opener operating properly.

Performed Safe & Sound Inspection on a 16x7 Wayne Dalton door with a Genie 2028 opener. Customer reported a suspected broken TorqueMaster spring and loose chain. Inspection revealed the TorqueMaster spring to be intact but improperly adjusted, preventing the opener from functioning correctly. Chain was confirmed loose, and a loose bolt was found at the track back hang. Hinges exhibited creaking and bearing plates produced a rhythmic squeak during operation.

Completed Safe & Sound Inspection on a 16x7 insulated Wayne Dalton door with mismatched torsion springs. Customer's sensor had fallen off track and was taped—door wouldn't operate. Reinstalled and aligned sensors; door restored to full operation. Lubricated hinges, springs, and rollers; tightened opener chain; greased rail. Paid by check. Door and opener fully operational.

A Nocatee homeowner called about a broken spring, but our Safe & Sound Inspection uncovered corroded cables, bottom fixtures, and a faulty sensor connection on both of her Clopay doors. Wagmore replaced the spring, cables, and bottom fixtures on both doors, corrected the sensor wiring, and performed full lubrication maintenance — leaving her with two doors that work the way they should.

Completed a Safe & Sound Inspection on a 16x7 Wayne Dalton door after the customer reported unusual noise. Inspection revealed the door needed a hinge adjustment, which we completed. Customer also enrolled in our maintenance plan to keep the door safe and running smoothly for years to come.

Safe & Sound Inspection on two doors. Performed a Safe & Sound Inspection on a 16x7 uninsulated door with a LiftMaster belt drive opener. Customer reported broken springs and cables. Inspection confirmed both springs were broken; cables had slipped off the drums but remained intact. Rollers showing wear, hinges dry.  Replaced both torsion springs and lubricated the door. Tested and confirmed door and opener operating properly.

Mr. Zreik stated his garage dr was noisey and would not open all the time. Installed LiftMaster 6690L opener with 7-ft rail; programmed 2 remotes, and 1 keypad. Full door rebuild: replaced springs, cables, rollers, bearings, bearing plates & shaft. Replaced failed bottom seal & retainer; set opener limits.

Completed Safe & Sound Inspection on a 16x7 Wayne Dalton Torque Master door with Genie 2028 Chain Drive opener. Customer reported no current issues; a previous concern had been resolved with reprogramming. Door and opener are in mostly good condition. Inspection revealed the Torque Master spring is oversized and not balancing the door properly.

Safe & Sound Inspection on two doors. 16x7 LiftMaster belt drive: found grinding rollers, loose belt, and previously damaged operator bracket. 16x8 LiftMaster chain drive: found off-center opener, unlevel back-hang brackets, and failed roller. Replaced rollers and operator brackets on both doors, correctly reinstalled 16x8 opener and brackets, lubricated all moving parts on both doors, reset limits, and programmed new 2-button remote to both doors.

A Nocatee customer called Wagmore believing both springs and cables were broken on their 16x7 overhead door. After a thorough Safe & Sound Inspection confirmed broken torsion springs and cables off the drums — but still intact — we replaced both springs, lubricated the door, and restored safe operation, backed by our lifetime spring warranty with bi-annual Wagmore servicing.

Upgraded both garage doors with new LiftMaster 2220L chain drive openers, torsion springs, cables, rollers, drums, bearing plates & bottom seals. Removed old extension springs & Craftsman openers.

Customer contacted us after both springs and a cable broke, leaving his garage door inoperable. We replaced the broken springs and cable, restoring full function to the door. He also enrolled in our maintenance plan to keep both of his garage doors operating safely and reliably for years to come.

Customer contacted us after their door came off the track and began making noise. We performed a full door system reset and rebalance to restore safe, smooth operation.

Performed Safe & Sound Inspection on a 16x7 Wayne Dalton door with Linear opener. Customer reported no maintenance in six years and raised concerns about exposed sensor wires. Inspection confirmed exposed and loose wiring on both safety sensors, a burnt-out lightbulb, missing pull cord handle, dry hinges causing black dust buildup, and a loud noise at full close due to an uneven door frame. Customer signed up for our three-year maintenance plan. Completed maintenance including lubrication of all hinges, rollers, bearings, springs, and opener rail; replaced the lightbulb; installed a pull cord handle; re-secured sensor wiring; and reset opener limits.

Our $0 Safe & Sound Inspection uncovered much more—a heavy torque master spring, plastic shavings, and wiring issues in her Genie opener. We replaced it with a new LiftMaster, programmed remotes and a keypad, and restored smooth, reliable operation.

Andy booked our $0 Safe & Sound Inspection for a noisy door that wouldn't open reliably. Our evaluation showed the door had reached end of life. We recommended a full replacement—no patches, just the right solution. Book yours today!

Our $0 Safe & Sound Inspection on two Wayne Dalton doors in Fruit Cove uncovered heavy spring balance, noisy hinges, and metal shavings from years of skipped lubrication—all before the customer ever noticed a problem. A full maintenance service restored smooth, quiet operation on both doors.

A customer's 16x8 insulated door and original linear opener had been noisy for years with no maintenance. Our $0 Safe & Sound Inspection uncovered missing opener screws and a door overdue for lubrication. We walked them through every finding, performed a full tune-up, installed new screws and an LED bulb, and significantly reduced the noise. They loved the results and joined our WAGs Family Plan. Book your $0 Safe & Sound Inspection today—fast, friendly, and focused on what matters most.

Inspection uncovered frayed cables, unbalanced door with light gaps, misaligned left drum, 2018 springs nearing end of life, and a loud opener past its prime. We recommended immediate cable replacement for safety and explained all findings. Garage door and opener currently functional.

John McClure requested our $0 Safe & Sound Inspection on their 16x7 insulated Wayne Dalton door with Genie 2028 chain drive opener. Our technician went through the entire door and found hinges and moving parts all in good condition. We tested settings and sensors and found everything in working order. We recommended maintenance at this time to keep the system performing optimally and programmed the customer's car to the garage door opener for added convenience.

This veteran homeowner requested our $0 Safe & Sound Inspection on her 16x7 Wayne Dalton insulated door with Genie 2028 opener and torque master spring. Our technician found the door and opener in working order overall, though the hinges were making excessive noise. We completed our complimentary veteran maintenance service with full lubrication to alleviate the creaks and cracks. We lubricated all moving parts, ran the door several times to ensure smooth operation, and reset the opener limits for optimal performance.

Our $0 Safe & Sound Inspection revealed his garage door and opener needed replacement—the panels were cracking and unsafe due to the door dating back to the 1990s.

Completed safe and sound inspection on 16 x 7 Wayne Dalton, torque master door with older genie chain drive opener. On arrival we found multiple issues with the door, including lack of lubrication, heavy, spring, and opener limits, not set properly, causing the door to open anytime it was closed. Brought all of our findings to the customer and explained everything in detail. Made recommendations to maintenance the door and reset the limits as well as to perform a torque master conversion and to replace the opener.

Eric Cabrera requested our $0 Safe & Sound Inspection on his 16x7 Wayne Dalton torque master door with Genie 2028 chain drive opener. Our technician found hinges making excessive noise and discovered the door needed realignment—the rollers required replacement to ensure the door would open and close smoothly.

Our inspection uncovered a failed opener and chain. The customer moved into the home a few years ago with existing openers already installed. No prior service or maintenance has been performed. During our Safe & Sound Inspection, we found the double door springs were original from 1997, while rollers had been previously replaced, and the door showed signs of past lubrication. Both openers had loose belts, and bottom seals on both doors were in poor condition. We reviewed all findings with the customer and recommended spring replacement on the double door and new bottom seals on both doors. Customer approved and signed an estimate for same-day service. We replaced bottom seals and retainers on both doors, installed new .243 springs on the double door, tested operation, and completed full lubrication and maintenance on both doors and openers.

Our inspection uncovered a failed opener and chain. We removed the old unit and installed a new LiftMaster 2220L with 7-foot chain rail. We replaced the 25-year-old springs from 1999 with new .250x2x30 LW and RW springs, installed 10 new nylon rollers, and verified proper spring tension and opener operation. After assisting with MyQ setup, we explained the warranties: lifetime parts and labor on springs and rollers, 3-year parts and labor on the opener. We demonstrated safe, proper operation. Customer was satisfied with the completed work.

During our inspection, we identified that the rollers and cables required replacement and adjustment. We also lubricated all components to ensure the garage door system was operating safely and functioning properly.

We completed our $0 Safe & Sound Inspection and discovered springs over ten years old requiring replacement. We also replaced the torsion shaft and bearings to ensure safe, optimal operation as designed.

Customer requested a high lift conversion quote and mentioned having springs replaced on the double door last year, while the single door still has original components. We discovered the year-old springs were never properly tensioned (making the door dangerously heavy) plus multiple maintenance issues on both systems, so with approval we completed full maintenance—adding proper tension, securing hardware, adjusting limits, and lubricating all components—leaving both doors quieter and functioning correctly.

Inspection revealed multiple safety concerns including dry-rotted bottom seal, improperly fastened opener J-arm, extremely loose chain nearly rubbing the door panels, and critically, original 2005 springs making the door dangerously heavy and causing cable deterioration. After explaining all findings in detail, I recommended maintenance service for minor issues like chain tensioning and lubrication, plus immediate spring replacement due to the dangerous configuration, which the customer approved.

 Customer wanted our Zero Safe & Sound Inspection. Customer enrolled in our maintenance plan and also purchased an emergency release arm and a new opener to ensure proper opening.

During the safety inspection, we discovered the operator bracket was barely secured to the door stile—two of three screws were nearly backed out completely. We also found the door was extremely heavy when disengaged from the opener. After weighing the door, we determined the current springs were undersized, causing the opener to strain when lifting. We presented our findings and explained the issues in detail. We recommended replacing the failed operator bracket with an adjustable operator bracket and replacing the springs with properly sized units. The incorrect spring size was causing excessive strain on all door.

Performed Safe & Sound Inspection on 10' x 7' pan door (circa 1980s) with extension spring system and Chamberlain chain drive opener (2014). The door operates but shows uneven movement due to aging extension springs. Extension springs are an outdated system that we do not service or support. Additional wear noted: rollers are worn; hinges and cables show rust deterioration. Informed customer of the deteriorating components and recommended full door replacement.

The customer reported no current issues with the door. They mentioned having the radius and other components replaced a few years ago. Our inspection confirmed most components have been upgraded, including quiet hinges and nylon 7-inch stem quiet rollers. The springs are original to the door, and both doors are currently balanced properly. However, the springs are a larger size than our standard stock. We informed the customer that we would prepare estimates for spring replacement and send them for future reference when replacement becomes necessary.

Upon arrival, the customer reported no current issues with either door but noted maintenance had been overdue. All components are original to the home from 2016. Both doors operated properly with functioning safety sensors and passed the reverse-on-contact test. However, we identified several maintenance needs: both doors were noisy, the LiftMaster chain drive required tension adjustment, and the single door with the side-mount opener was making contact with exterior trim, causing it to jump during operation. Both doors showed an acceptable balance despite having 10-year-old original springs. We recommended maintenance and lubrication for both doors, plus replacement of the improperly installed outdoor trim affecting the side-mount opener.

Customer stated on arrival that they were having issues with their keypad. We performed a comprehensive inspection of the door and opener, testing all components. Most door components are original equipment from the early 2000s, though the customer reported having the spring replaced previously. During testing, we determined that the keypad had failed and required replacement. We presented the customer with a replacement option, received their approval on the estimate, and proceeded with installation. The new keypad was programmed with the customer's desired code and tested to confirm proper operation with the opener.

Fruit Cove Homeowner Gets Peace of Mind - With $0 Inspection 

Jeff Pearce requested a free Safe & Sound Inspection to ensure his garage door was operating safety. Our experts checked all components for wear, damage, and proper funtion-helping prevent accidents, breakdowns, and costly repairs down the road. 

No Surprises. Just smart upkeep. 

St. Johns Homeowner Tackles Garage Jerking - With $0 Inspection 

Henry McCann noticed his garage jerking during opening. Our free Safe & Sound Inspection revealed it needed lubrication and sensor updates. He enrolled in our 1-year maintenance plan to keep things smooth and safe. 

No panic. Just smart prevention

St. Augustine Homeowner Solves Jerky Garage Door - With $0 Inspection

Melissa Harrell noticed her garage would jerk while opening, then self-correct. Our free Safe & Sound Inspection revealed the 16x7 door wasn't properly balanced - a simple fix that prevented future wear and tear.

No drama. Just smart diagnostics. 

Customer wanted our zero safe and sound inspection. Inspection revealed heavy spring balance with springs dated 2015 (too fatigued for adjustment at 10+ years old), plus loose chain and cover on the opener and screeching hinges.

St. Johns Homeowner Gets a Garage Door Rebuild - With Full Transparency

Lillie Nay's opener had failed, forcing manual operation. Her home was older, and the garage door's history was unknown. Our free Safe & Sound Inspection revealed worn springs, rollers, and a broken trolley. We provided a clear estimate to rebuild the door and install a new LiftMaster 8500W opener with a 7-foot belt rail. 

No guesswork. Just clarity and control.

St. Augustine Homeowner Avoids Major Garage Trouble - For $0 

Lisa Mimnaugh called Wagmore to investigate a MY Q system. During our free Safe & Sound Inspection, we found a worn belt/chain opener and flagged it before failure. she chose to upgrade with a full MY Q system for added safety and control. 

No pressure. Just smart prevention.

St. Johns Homeowner Silences Garage Noise-With $0 Help

Jason Beggs reached out about a noisy garage door. Our free Safe & Sound Inspection revealed it just needed lubrication - no repairs required. He enrolled in our maintenance plan to keep things smooth and quit year-round. 

No upsell. Just honest care.

St. Johns Homeowner Gets Lubrication + Sensor Fix - With $0 Inspection 

Stan Clyer requested a free Safe & Sound Inspection to stay ahead of garage issues. We found he needed lubrication and new sensors- no major repairs. He signed up for our 1-year maintenance plan to keep things running smoothly.

No surprises. Just smart upkeep.